Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux)

[delle54]

Yep, chasing that pot of gold. it lasted less then a week, imagine if we had v6 miner on day one...... I'm sticking with NH for now, saves a lot of time exchanging coins for BTC as I have no intention of holding anything but BTC and ETH long term.

Yeah, but you have no choice to sell your ZEC at a good price.

[Tmdz]

Yep, chasing that pot of gold. it lasted less then a week, imagine if we had v6 miner on day one...... I'm sticking with NH for now, saves a lot of time exchanging coins for BTC as I have no intention of holding anything but BTC and ETH long term.

Yeah, but you have no choice to sell your ZEC at a good price.

I would not worry about holding zec until the full block reward is reached.  Reason I use nicehash is so I don't lose money as the coin loses value.

[mettalmag]

Good Job Man!!!!!
windows screen capture

How are you keeping your temps that low, my 390x sits at 93c

93 is too high I'm using -tstop on 80
try cleaning them from dust maybe it'll help
also considering that V5 was way cooler than v4 and v6 is same as v5, I can't imagine what temps will you get on mining ETH

here are mines

still cold until now

so jealous of your temps, i only have one 390x the rest are 270x and 280x. will probably remove the blackplate to see if it helps

I have a quite big air vent and windows slightly open and what I observed is which miners are close to window have higher temps then others. I think it's all about dust, I'm going to clean them maybe this weekend so I'll post what will happen next..

[MEDVEDja2]

Great miner Claymore! Thx!

My stats:

R9 7950/7970/280/280x = 110-120 S/s
R9 290 = 135-140 S/s
RX 470 8G = 148-151 S/s

All in default mode. No crashes.

[klondike_bar]

so jealous of your temps, i only have one 390x the rest are 270x and 280x. will probably remove the blackplate to see if it helps

Imo the backplate is probably better and/or inconsequential if left on. In some builds, it may actually help conduct heat from the card (while others it provides an insulating layer)

[Trimegistus]

These are my temperatures:



 

6x480 4GB underclocked & undervolted

[fr4nkthetank]

I hate to repeat myself, but has anyone else noticed that the dev fee varies from 10-90 seconds?

yup.  no idea why though.

[delle54]

THX. The first reply since v6 apeared.
Claymore seems to have reduced his average fee.

[adaseb]

These are my temperatures:



 

6x480 4GB underclocked & undervolted

Your speeds are very slow however. So it doesn't make sense doing this since the power is still cheaper than the gains you get by running it at stock speeds.

[Claymore]

THX. The first reply since v6 apeared.
Claymore seems to have reduced his average fee.

Please check "FAQ" section in first post. Measure time between "DevFee: start mining" and "DevFee: stop mining and disconnect" strings. It's always 90sec.

[Trimegistus]

Your speeds are very slow however. So it doesn't make sense doing this since the power is still cheaper than the gains you get by running it at stock speeds.

That's your opinion. I rather have slower speeds without noise or heat, than higher speeds with higher consumption, noisy fans and a lot of heat generation.

But that's me...  

[qqqq]

6xR9 380 periodically resets GPU0 speed, and the miner errors appear non-existent cards, with which it can be connected?

It's a bug, will be fixed in next update. Divide card number by 2.

How soon will be next update ?

[Claymore]

6xR9 380 periodically resets GPU0 speed, and the miner errors appear non-existent cards, with which it can be connected?

It's a bug, will be fixed in next update. Divide card number by 2.

How soon will be next update ?

Do you want more speed?

[HardwarePal]

6xR9 380 periodically resets GPU0 speed, and the miner errors appear non-existent cards, with which it can be connected?

It's a bug, will be fixed in next update. Divide card number by 2.

How soon will be next update ?

Do you want more speed?

500% speed increase and 20% dev fee would be fine with me

[delle54]

Measure time between "DevFee: start mining" and "DevFee: stop mining and disconnect" strings. It's always 90sec.

I do this every time the purple text appears since 2 days. Maybe I interpret something wrong. You are the "boss" (and a very good one).

[Tmdz]

6xR9 380 periodically resets GPU0 speed, and the miner errors appear non-existent cards, with which it can be connected?

It's a bug, will be fixed in next update. Divide card number by 2.

How soon will be next update ?

Do you want more speed?

No.  Its fast enough and besides more speed won't give more profit anyway.

Id prefer if possible more efficient for lower watts over speed.

[Claymore]

Measure time between "DevFee: start mining" and "DevFee: stop mining and disconnect" strings. It's always 90sec.

I do this every time the purple text appears since 2 days. Maybe I interpret something wrong. You are the "boss" (and a very good one).

Ok I'll make these lines purple too so you can see it.

[adaseb]

Something is messed up with all the pools.

Can't connect to Nicehash, Flypool. When it connects 50% rejects OR 2000ms ping times.

ZEC NETWORK UNDER ATTACK???

[HardwarePal]

Something is messed up with all the pools.

Can't connect to Nicehash, Flypool. When it connects 50% rejects OR 2000ms ping times.

ZEC NETWORK UNDER ATTACK???

Fine on my end...

[forato]

Is there a way to view the remote rig with ethman or any way when we have rigs in diferents places? I have some on different networks but only can control the rigs that are in the same one..