OLD: BFGMiner 3.10.0: modular ASIC+FPGA, GBT+Strtm, RPC, Mac/Lnx/W64, AntU1, DRB

[Juzz]

...snip...

I get segmentation fault when trying to launch that bfgminer - I am on an Ubuntu x86 latest version, I've compiled hidapi myself since there wasn't any in the repositories...

Try running bfgminer under sudo permissions.

That seg faults as well, but now the prompts are no longer on separate lines (when pressing enter).

AHA!
I just renamed my bfgminer.conf and now it starts up!

[darcimer]

Hello with https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z, and
bfgminer -S antminer:all -S erupter:all, it goes with my erupter an antminer but my nanofurys no more go why?

 with bfgminer3.9 and only -S erupter:all i see my nanofury and my erupters.

without zadig.

how my nanofury, erupters and antminers go on windows???


setup :

1* dlink 10 port usb hub  -> 2 erupters and 2 nanofurys   3.5A power
1* delock 7 port hub -> 3 antminer 3.5A power
and individual an two differnt usb ports on my pc
so i have enough power i think.

Could someone please explain to me how to use the binaries?  I downloaded them, but I have no idea what to do with them now that I have them.  I am trying to run some U1's on an anker 9 port hub, and all I am getting is icarus..
Thanks!

~D

[Taugeran]

Hello with https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z, and
bfgminer -S antminer:all -S erupter:all, it goes with my erupter an antminer but my nanofurys no more go why?

 with bfgminer3.9 and only -S erupter:all i see my nanofury and my erupters.

without zadig.

how my nanofury, erupters and antminers go on windows???


setup :

1* dlink 10 port usb hub  -> 2 erupters and 2 nanofurys   3.5A power
1* delock 7 port hub -> 3 antminer 3.5A power
and individual an two differnt usb ports on my pc
so i have enough power i think.

Could someone please explain to me how to use the binaries?  I downloaded them, but I have no idea what to do with them now that I have them.  I am trying to run some U1's on an anker 9 port hub, and all I am getting is icarus..
Thanks!

~D

you need to use -S antminer:all in the command line

optionally if you wish to OC them a tad add --set-device antminer:freq=0981

this will set the clock to 250 MHz and produce ~2.0Gh/sec


view https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner-U1%20user%20guide.pdf
for a table of frequencies

[darcimer]

Hello with https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z, and
bfgminer -S antminer:all -S erupter:all, it goes with my erupter an antminer but my nanofurys no more go why?

 with bfgminer3.9 and only -S erupter:all i see my nanofury and my erupters.

without zadig.

how my nanofury, erupters and antminers go on windows???


setup :

1* dlink 10 port usb hub  -> 2 erupters and 2 nanofurys   3.5A power
1* delock 7 port hub -> 3 antminer 3.5A power
and individual an two differnt usb ports on my pc
so i have enough power i think.

Could someone please explain to me how to use the binaries?  I downloaded them, but I have no idea what to do with them now that I have them.  I am trying to run some U1's on an anker 9 port hub, and all I am getting is icarus..
Thanks!

~D

you need to use -S antminer:all in the command line

optionally if you wish to OC them a tad add --set-device antminer:freq=0981

this will set the clock to 250 MHz and produce ~2.0Gh/sec


view https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner-U1%20user%20guide.pdf
for a table of frequencies

I think you are a couple steps ahead of me.  The binaries are in a .7z file, and I can't open it.  I think once I can run it, I will be able to enter the right commands.  I'm using XP.

[AbiTxGroup]

I think you are a couple steps ahead of me.  The binaries are in a .7z file, and I can't open it.  I think once I can run it, I will be able to enter the right commands.  I'm using XP.

Try 7-zip portable

http://portableapps.com/apps/utilities/7-zip_portable

or....

the full version at http://www.7-zip.org/

[Codemeister]

Is the overclock limited to 2 GH/s?

[asjfdlksfd]

I didn't found my last post of my request. So may I ask again for a little Chilly extension:

Can we have a ZlX (with lowercase) extension or an us of ZcX instead ZGX in the "M" menu to see also all the ASIC temperatures at runtime?. Generally the Identify command is not working. Maybe it can be used more for detailed informations:

Select processor to manage using up/down arrow keys
BFL 1 : 29.0C | OFF  /27.72/26.45Gh/s | A: 1069 R: 9+ 0(.83%) HW: 21574/3.8%
  BitFORCE SHA256 SC from MrTeal and ChipGeek
Serial: FTWZA0ON
Kernel: bulk queue
Temperatures: 29.0C 27.0C
Voltages: 3.290 / 1.161 / 12.187

[E]nable dentify [F]an control
[Slash] Find processor  [Plus] Add device(s)  [Enter] Close device manager

Here generally I want to get all the temperatures from ZlX command also in the Devices menu (M):
PROCESSOR 0: 36.25 C
PROCESSOR 1: 31.00 C
PROCESSOR 2: 38.00 C
PROCESSOR 3: 33.25 C
PROCESSOR 4: 35.00 C
PROCESSOR 5: 33.75 C
PROCESSOR 6: 34.00 C
PROCESSOR 7: 31.75 C

Or use ZcX instead of ZCX to add temperatures to the Chip lines for less precision for a first implementation
DEVICE: Chili SC
MANUFACTURER: MrTeal and ChipGeek
FIRMWARE: 1.2.14e
CHIP PARALLELIZATION: NO
QUEUE DEPTH:40
PROCESSOR 0: 12 engines @ 339 MHz -- MAP: FFE1 37 C
PROCESSOR 1: 8 engines @ 323 MHz -- MAP: 0FF0 32 C
PROCESSOR 2: 16 engines @ 356 MHz -- MAP: FFFF 39 C
PROCESSOR 3: 9 engines @ 314 MHz -- MAP: 07FA 34 C
PROCESSOR 4: 16 engines @ 297 MHz -- MAP: FFFF 36 C
PROCESSOR 5: 7 engines @ 257 MHz -- MAP: 807B 34 C
PROCESSOR 6: 13 engines @ 330 MHz -- MAP: FFE3 35 C
PROCESSOR 7: 8 engines @ 307 MHz -- MAP: 0FF0 32 C
THEORETICAL MAX: 28.46 GH/s
ENGINES: 89
FREQUENCY: 319 MHz
CRITICAL TEMPERATURE: 0
TOTAL THERMAL CYCLES: 0
XLINK MODE: MASTER
XLINK PRESENT: NO
OK

[HellDiverUK]

Just picked up a Bitburner Fury - how is bfg's support for these things?

Also got a Bitburner XX (Avalon chips).  Again, I assume bfg supports these things?

[ice56]

Hello with https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z, and
bfgminer -S antminer:all -S erupter:all, it goes with my erupter an antminer but my nanofurys no more go why?

 with bfgminer3.9 and only -S erupter:all i see my nanofury and my erupters.

without zadig.

how my nanofury, erupters and antminers go on windows???


setup :

1* dlink 10 port usb hub  -> 2 erupters and 2 nanofurys   3.5A power
1* delock 7 port hub -> 3 antminer 3.5A power
and individual an two differnt usb ports on my pc
so i have enough power i think.

Could someone please explain to me how to use the binaries?  I downloaded them, but I have no idea what to do with them now that I have them.  I am trying to run some U1's on an anker 9 port hub, and all I am getting is icarus..
Thanks!

~D

you need to use -S antminer:all in the command line

optionally if you wish to OC them a tad add --set-device antminer:freq=0981

this will set the clock to 250 MHz and produce ~2.0Gh/sec


view https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner-U1%20user%20guide.pdf
for a table of frequencies

ok step by step
1. i Downloadet https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z,
2. extrakt
3. copy zlib1 (32bit) to extrakt folder
4. put Logindata in conf file
5. start with cmd file with this line: "bfgminer -S antminer:all -S erupter:all"
6. bfgminer only found the 3 antminer and the 2 erupter, but my nanofurys not there and not found with Managment Devices.

WHY? because when i downloadet bfgminer 3.8 or 3.9 and start with "bfgminer -S all" or "bfgminer -S erupter:all" then my 2 nanofurys are in bfgminer and the 2 erupter too.
why not with this npw-antminer edition? is there compiled without nanofurys? but other post´s i read in this topic it goes at there

why i dont compile it myself? because i have probs with compiler in ./configure part
my compiler dont found "autoreconf" and i dont found solution atm.

[rmolby]

Hello with https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z, and
bfgminer -S antminer:all -S erupter:all, it goes with my erupter an antminer but my nanofurys no more go why?

 with bfgminer3.9 and only -S erupter:all i see my nanofury and my erupters.

without zadig.

how my nanofury, erupters and antminers go on windows???


setup :

1* dlink 10 port usb hub  -> 2 erupters and 2 nanofurys   3.5A power
1* delock 7 port hub -> 3 antminer 3.5A power
and individual an two differnt usb ports on my pc
so i have enough power i think.

Could someone please explain to me how to use the binaries?  I downloaded them, but I have no idea what to do with them now that I have them.  I am trying to run some U1's on an anker 9 port hub, and all I am getting is icarus..
Thanks!

~D

you need to use -S antminer:all in the command line

optionally if you wish to OC them a tad add --set-device antminer:freq=0981

this will set the clock to 250 MHz and produce ~2.0Gh/sec


view https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner-U1%20user%20guide.pdf
for a table of frequencies

ok step by step
1. i Downloadet https://www.dropbox.com/s/z29x4n6ng510joi/bfgminer-npw-antminer.7z,
2. extrakt
3. copy zlib1 (32bit) to extrakt folder
4. put Logindata in conf file
5. start with cmd file with this line: "bfgminer -S antminer:all -S erupter:all"
6. bfgminer only found the 3 antminer and the 2 erupter, but my nanofurys not there and not found with Managment Devices.

WHY? because when i downloadet bfgminer 3.8 or 3.9 and start with "bfgminer -S all" or "bfgminer -S erupter:all" then my 2 nanofurys are in bfgminer and the 2 erupter too.
why not with this npw-antminer edition? is there compiled without nanofurys? but other post´s i read in this topic it goes at there

why i dont compile it myself? because i have probs with compiler in ./configure part
my compiler dont found "autoreconf" and i dont found solution atm.

Someone correct me if I am wrong since I don't own a fury, but I think all you have to do is also add this to the command line

Code:

-S bigpic:all

and it will probe for the furys.

[Luke-Jr]

Just picked up a Bitburner Fury - how is bfg's support for these things?

Also got a Bitburner XX (Avalon chips).  Again, I assume bfg supports these things?

Not sure why you assume that.
Bitburner still hasn't provided and docs, sample units, code, or even communicated.

[HellDiverUK]

Just picked up a Bitburner Fury - how is bfg's support for these things?

Also got a Bitburner XX (Avalon chips).  Again, I assume bfg supports these things?

Not sure why you assume that.
Bitburner still hasn't provided and docs, sample units, code, or even communicated.

I assumed it did because most devs are fothcoming with stuff like that.  Or they worked similarly to some other device, I don't know.  That's kind of why I asked.

Fair enough, looks like cgminer it is then.

Edit:  From cgminer's readme file:

Code:

All current BitBurner devices (BitBurner X, BitBurner XX and BitBurner Fury)
emulate Avalon devices, whether or not they use Avalon chips.

So, is there a chance bfg will work?  I guess I'll just have to try it when the boards arrive.

[HellDiverUK]

Still having issues getting the Nanofurys to work on nwooll's version of bfg.  Running it on Debian, hidapi is installed correctly as far as I can tell (no warning or errors when setting up bfg).

Any ideas?

[Taugeran]

Just picked up a Bitburner Fury - how is bfg's support for these things?

Also got a Bitburner XX (Avalon chips).  Again, I assume bfg supports these things?

Not sure why you assume that.
Bitburner still hasn't provided and docs, sample units, code, or even communicated.

I believe they emulate Avalon units with the mcu. So -S Ava:/path/to/bitburner may work

I might try adjusting the --Avalon-options to follow the bit burner formula.

And looking at cg's driver, btb is a sub driver

[HellDiverUK]

Yeah, reading on down the ASIC.README I saw that.  I'll update when I try.

[nwoolls]

Someone correct me if I am wrong since I don't own a fury, but I think all you have to do is also add this to the command line

Code:

-S bigpic:all

and it will probe for the furys.

The bigpic driver is for Red Fury / Blue Fury - the BF1 devices. The nanofury driver is for Ice Fury and other NanoFury (NF1) based devices.

[Taugeran]

Also. What software driver is needed to comm with the Klondike series.  Receiving 2 later today

[Luke-Jr]

Also. What software driver is needed to comm with the Klondike series.  Receiving 2 later today

Klondike is a direct USB device, so use Zadig for it.

[Taugeran]

Also. What software driver is needed to comm with the Klondike series.  Receiving 2 later today

Klondike is a direct USB device, so use Zadig for it.

So Lib USB is all I need on a BBB.  And -S kln:/path/to/Klondike ?

Normally I could figure it out but I'm sleep deprived, etc. the usual

[chadgroover]

Working perfectly with 5x U1 on Windows 7 x64

Makes such a welcome change to not have to piss about with unplugging all but 1 device before you can start cgminer!