|
marvykkio
|
 |
April 25, 2015, 10:39:48 AM |
|
I'm buying the thermal paste arctic mx-4, 20 grams, can be enough to change in 4x antminer s5? I want to change it in all the miners
|
|
|
|
|
|
|
|
marvykkio
|
|
April 25, 2015, 12:24:19 PM |
|
well I think that there is nothing else to do, just send in the warranty miner, the problem and resubmitted  |
|
|
|
|
|
|
Tupsu
Legendary
 Offline
Activity: 1204
Merit: 1003
|
|
April 25, 2015, 01:22:03 PM |
|
I was told that for s5 overclocking voids the warranty, my miner was ..........
sorry if the question will void your warranty because putting this function?
Yes. However, you can erase your pictures and change posts. |
|
|
|
|
|
marvykkio
|
|
April 25, 2015, 01:40:30 PM |
|
now the picture is already been sent to the guarantee, I can not do anything anyway, and both seem to me bullshit
|
|
|
|
|
|
marvykkio
|
|
April 25, 2015, 01:44:11 PM |
|
the problem is not the 25M more overclocking, and because it was defective factory, if you do not want to change it, do not buy more from bitmain, why and asurdo not change the product purchased from 1 week ago
and I only used psu good, 1 x 1 psu miner, RM1000 CORSAIR GOLD
|
|
|
|
|
|
hanti
|
|
April 25, 2015, 03:14:11 PM |
|
why did u even try to oc it if it was broken....
|
|
|
|
|
|
Tupsu
Legendary
Offline
Activity: 1204
Merit: 1003
|
|
April 25, 2015, 05:57:33 PM |
|
Cries will not help here. I'm happy with my 40 TH/s Antminer S5. The best miner at the moment. |
|
|
|
|
|
marvykkio
|
|
April 25, 2015, 06:24:45 PM |
|
I apologize for the caps lock  |
|
|
|
|
|
marvykkio
|
|
April 25, 2015, 06:28:12 PM |
|
but my fear and I did not replace the blades, also because I bought with pleasure from them, and I trust, however, can not tell me that the problem and because they found the frequency to 375m, when the defoult and 350M, I do not think that this is the fault 25M more? by I noticed that when I move the connectors 6 pin pci the blade back to work, but after a while back as before and I have to go back to touch the connector, and a lack of solder connectors  |
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
|
April 25, 2015, 06:31:32 PM |
|
@marvykkio,
Your case is reviewed by Bitmain USA now. Please wait for a few days. Bitmain_D will look into your Hashing PCB problem further. Please check your e-mail for further instruction!
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA |
|
|
|
marvykkio
|
|
April 25, 2015, 06:35:12 PM |
|
hi we are happy that you're here, you've seen in the photo and shared? this happens as I move the connectors 6 pin pci, through no fault of overclocking as I have written,
|
|
|
|
|
|
marvykkio
|
|
April 25, 2015, 07:00:58 PM |
|
nothing to do and the problem came back, expect are felt  |
|
|
|
|
|
jtoomim
|
|
April 25, 2015, 08:35:07 PM |
|
nothing to do and the problem came back, expect are felt It's possible that you have an intermittent problem. When the problem shows up, can you make it go back to full hashrate by restarting cgminer? (That's what the Save & Apply button does on the pool configuration page.) If so, and if Bitmain doesn't RMA this device, you may be able to get it to work pretty well by setting up a cron job to run "/etc/init.d/cgminer restart" every few hours. The default Bitmain firmware doesn't include cron, but smit1257's does. Of course, using smit1257's firmware voids your warrantee unless you do it with explicit permission from Bitmain, so you shouldn't do it without asking permission. Can you show us your hashrate graphs on the pool side? |
Hosting bitcoin miners for $65 to $80/kW/month on clean, cheap hydro power. http://Toom.im |
|
|
|
dog1965
|
|
April 25, 2015, 10:29:10 PM |
|
but my fear and I did not replace the blades, also because I bought with pleasure from them, and I trust, however, can not tell me that the problem and because they found the frequency to 375m, when the defoult and 350M, I do not think that this is the fault 25M more? by I noticed that when I move the connectors 6 pin pci the blade back to work, but after a while back as before and I have to go back to touch the connector, and a lack of solder connectors Could be a bad ribbon cabble. Or that you are using SHITHASH as your pool. |
|
|
|
|
notlist3d
Legendary
Offline
Activity: 1456
Merit: 1000
|
|
April 26, 2015, 12:51:46 AM |
|
but my fear and I did not replace the blades, also because I bought with pleasure from them, and I trust, however, can not tell me that the problem and because they found the frequency to 375m, when the defoult and 350M, I do not think that this is the fault 25M more? by I noticed that when I move the connectors 6 pin pci the blade back to work, but after a while back as before and I have to go back to touch the connector, and a lack of solder connectors Could be a bad ribbon cabble. Or that you are using SHITHASH as your pool. I would try it with antminer pool and see how it works. Nicehash works great with some and others not so much. So defiantly try that before going any deeper into the inspection. |
|
|
|
|
|
Darthswan
|
|
April 26, 2015, 02:06:31 AM |
|
Lately this S5 has been dropping in hash rate. Has anyone else been having this issue? It's getting annoying now. Especially when it decides to go south when the pool finds a block.
|
|
|
|
notlist3d
Legendary
Offline
Activity: 1456
Merit: 1000
|
|
April 26, 2015, 02:33:10 AM |
|
Lately this S5 has been dropping in hash rate. Has anyone else been having this issue? It's getting annoying now. Especially when it decides to go south when the pool finds a block.
No issues that I have noticed. Same normal hashrate. Only thing is every once in a while 1 blade quits and i need to restart. I'm guessing twice a week. |
|
|
|
|
|
