Swedish ASIC miner company kncminer.com

[Phoenix1969]

Could you use the flat bar (on the processor side) and the integrated bracket that came unglued to make a sandwich around the heatpipes?  Then use a c-clamp or locking pliers (vise-grips) to squeeze all four pipes back into proper alignment?

Just use a full tube of thermal paste! That'll fix it right up! lol

or you could just buy a new one.

to easy.. job done  

That's crazy talk, man!  Just too damn easy for these hardy young DIYers  He could save a couple bucks if he doesn't cook this expensive piece of almost irreplaceable electronic equipment  Lol

Actually I already ordered one for the damaged that came from Phoenix. I will try to fix the November damaged cooler and if I don't success I will order another one.

Indeed strange. The cooler that was separately wrapped, is the one I bought from Amazon, and brand-new. I'm guessing that one of the attached coolers got forced backward/forward during shipping in a violent drop or something...  the weight of the loose cooler may have added to the weight of the cooler it was next to, causing the bend during a drop. Or even was a defect, and I never saw it.  I crammed as much bubble wrap as I could humanly fit into the box...Next time, no extra stuff in the case...  sorry to hear Cypher.  You got such a super deal though, it should be no problem for a heatsink...  The entire box was  insured for 10 grand... but a 30 dollar claim would hardly be worth it. I'm actually kinda jealous that the "finicky" extra  board is ace now, and totally scratching my head..... which for me, adds further speculation to the heatsink....       tunung suite?
You da man Cypher!

[soy]

Does anyone know what the typical support e-mail reply time is nowadays?  I had a nice fireworks display on one of my Oct. Jupiter's when upgrading PSUs and haven't heard anything from them for a couple of days now aside from the auto reply. Just curious how long it will take to issue RMA.

What the bloody did you do? All you have to do is swap cables.

And that is precisely what i did.  I was going from a Coolermaster v1000 to a nice Corsair AX1200 gold.  Brand new out of the box never used, plug it all in, hit the switch and poof.......Fire!  That was my good Jupiter too.

Here is the aftermath.

For this reason I think the plugs having both a jumper and a power resistor to the 3v line are a very good bet.  I know you followed instructions, but did you put in the jumper then fire up the supply and check that the voltage was there on the 12V, then shut down the supply, plug the power supply into the Jupiter, then switch on the supply?

If my theory that the current ramp, preventing current surge producing a voltage spike sufficient to blow the caps, the current ramp to ramp up current on the 12V line is actually controlled by a voltage ramp of 0 to 1V produced on the 3.3V line (because the 3.3V will be up to regulated voltage before the 5V or 12V) then putting in the jumper, turning on the supply to check if the jumper is correct and voltage being supplied, then shut down before plugging into Jupiter, since the supply expects that it is plugged into a motherboard having a load on the 3.3V line, it expects that when the supply is turned off the 3.3V line filter capacitors will drain out thru the motherboard.  That can't happen without a motherboard or a resistor to ground from the 3.3V line as well as the jumper.  

So, if  you check the jumper was correctly placed by looking for 12V on the 12V line, then shut down, plugged the supply into the Jupiter, and turned it on, the supply 3.3V line never drained and still had full voltage on its filter caps and the timed ramp voltage that controlled the ramp for the 12v current had remained at max, as if already having timed out its ramp, and BANG, instant max current.

[Phoenix1969]

That's it.... I'm selling my Corsair ax1200's... remember the HX series before?  I'm abandoning Corsair.
Too coincidental. Scary, because I always did the jumper test first, just as soy describes.. and he's absolutely correct saying those caps hold a charge!

[canth]

So received my Nov Jupiter.

Can't connect to machine by either SSH or webpage.  It is assigned an IP address just can't connect. Even ping gets no response but not sure if the BBB is setup to respond to ping.

If I disconnect all 4 ASIC boards I can connect to the host and access web gui with no issues.  
Reconnect the ASIC boards, can't connect.  
Tried connecting just one ASIC board with same results.
Tried two different power supplies with the same results.

Anyone had anything like this or am I just SOL?

Have you tried all 4 ASIC boards individually (1 plugged in at a time)? I would try that first.

[soy]

I'm mourning a dead Blade today, my one and only.  It's come up with all xxxxxxxxxxxxxxxx for the ASICs.  We had a warm December day in Georgia, 71.6°F out and 76.0°F in the room.

I couldn't bring myself to buy a Neptune.  Just too much for me.  That the Neptunes aren't sold out yet tempts me right now.  But no.  Ah, the falling BTC harvest, now accelerated losing 10GH/s.  It's like aging.

[r1senfa17h]

Anyone else have a die that shows up as "off" in BertMod?



With SPI voltage at 3.3v, I've tried adjusting the individual die voltage from the lowest to the highest without effect.

[CYPER]

Does anyone know what the typical support e-mail reply time is nowadays?  I had a nice fireworks display on one of my Oct. Jupiter's when upgrading PSUs and haven't heard anything from them for a couple of days now aside from the auto reply. Just curious how long it will take to issue RMA.

What the bloody did you do? All you have to do is swap cables.

And that is precisely what i did.  I was going from a Coolermaster v1000 to a nice Corsair AX1200 gold.  Brand new out of the box never used, plug it all in, hit the switch and poof.......Fire!  That was my good Jupiter too.

Here is the aftermath.

For this reason I think the plugs having both a jumper and a power resistor to the 3v line are a very good bet.  I know you followed instructions, but did you put in the jumper then fire up the supply and check that the voltage was there on the 12V, then shut down the supply, plug the power supply into the Jupiter, then switch on the supply?

If my theory that the current ramp, preventing current surge producing a voltage spike sufficient to blow the caps, the current ramp to ramp up current on the 12V line is actually controlled by a voltage ramp of 0 to 1V produced on the 3.3V line (because the 3.3V will be up to regulated voltage before the 5V or 12V) then putting in the jumper, turning on the supply to check if the jumper is correct and voltage being supplied, then shut down before plugging into Jupiter, since the supply expects that it is plugged into a motherboard having a load on the 3.3V line, it expects that when the supply is turned off the 3.3V line filter capacitors will drain out thru the motherboard.  That can't happen without a motherboard or a resistor to ground from the 3.3V line as well as the jumper.  

So, if  you check the jumper was correctly placed by looking for 12V on the 12V line, then shut down, plugged the supply into the Jupiter, and turned it on, the supply 3.3V line never drained and still had full voltage on its filter caps and the timed ramp voltage that controlled the ramp for the 12v current had remained at max, as if already having timed out its ramp, and BANG, instant max current.

So how can one prevent this from happening?
Shut down the PSU from the switch at the back, unplug from the socket and then remove and insert the jumper a couple of times to discharge everything?

[tolip_wen]

CYPHER

Now I understand your agressive inverse trolling recently.
(engage a troll and 'you are what you resent')

I wonder if you got the unit pheonix 'twisted' the cooler on.
Remember that amazing 'fix' ?

[DPoS]

just stopped in to say...    'if you would of just bought BTC instead of ...  blah blah'  

anyone want mark down all the coins they could of sold at 1100+ ??  


.. as you were

[merv77]

So received my Nov Jupiter.

Can't connect to machine by either SSH or webpage.  It is assigned an IP address just can't connect. Even ping gets no response but not sure if the BBB is setup to respond to ping.

If I disconnect all 4 ASIC boards I can connect to the host and access web gui with no issues.  
Reconnect the ASIC boards, can't connect.  
Tried connecting just one ASIC board with same results.
Tried two different power supplies with the same results.

Anyone had anything like this or am I just SOL?

have you tried disconnecting the data cables to the ASIC boards but leave the power connected?  Not that this will fix anything but you can eliminate the ASIC boards are faulty.

just to see if it's a comms problem, because that's what it seems.
and only because you say all the asic boards are doing the same thing.

[DeathAndTaxes]

So received my Nov Jupiter.

Can't connect to machine by either SSH or webpage.  It is assigned an IP address just can't connect. Even ping gets no response but not sure if the BBB is setup to respond to ping.

If I disconnect all 4 ASIC boards I can connect to the host and access web gui with no issues.  
Reconnect the ASIC boards, can't connect.  
Tried connecting just one ASIC board with same results.
Tried two different power supplies with the same results.

Anyone had anything like this or am I just SOL?

have you tried disconnecting the data cables to the ASIC boards but leave the power connected?  Not that this will fix anything but you can eliminate the ASIC boards are faulty.

just to see if it's a comms problem, because that's what it seems.
and only because you say all the asic boards are doing the same thing.

Ok so:
all boards data cables disconnected + power cable connected = boot & login
all boards data cables disconnected + power cable disconnected = boot & login
any 1 ASIC board data cable connected + power cable connected = dead

At this point I have to think it is an issue with the control board.  Obviously my amazing luck.  Anything else failing would leave me with some hashing power.

On edit: a weird possibly related issue.  Any settings made on the host (i.e. setting pool config or enabling SSH) are lost when powering off and on.

[vesperwillow]

just stopped in to say...    'if you would of just bought BTC instead of ...  blah blah'  

anyone want mark down all the coins they could of sold at 1100+ ??  


.. as you were

You mean the ones I sold at 1200? Buying time is coming up soon

I'm mourning a dead Blade today, my one and only.  It's come up with all xxxxxxxxxxxxxxxx for the ASICs.  We had a warm December day in Georgia, 71.6°F out and 76.0°F in the room.

I couldn't bring myself to buy a Neptune.  Just too much for me.  That the Neptunes aren't sold out yet tempts me right now.  But no.  Ah, the falling BTC harvest, now accelerated losing 10GH/s.  It's like aging.

That sucks... 76* killing it ? Is it a really oooold blade?

Anyone else have a die that shows up as "off" in BertMod?



With SPI voltage at 3.3v, I've tried adjusting the individual die voltage from the lowest to the highest without effect.

Is there any benefit to bertmod if your KNC equipment is hashing well above spec'd rate?

[RickJamesBTC]

Lots of snow falling here, still no problems with the Jupiter. Eligius 12hr hashrate avg is steadily climbing, currently at 650gh.  Someone asked if there was a difference case on or off. I saw no hash rate difference with either, so right now the case is on to keep it looking good.

Guys replacing heatsinks, is there a better than stock replacement out there if we run into issues in the future overclocking them? I think the current heatsinks are pretty good.

[xstr8guy]

just stopped in to say...    'if you would of just bought BTC instead of ...  blah blah'  

anyone want mark down all the coins they could of sold at 1100+ ??  


.. as you were

HAHAHA!

Sure glad I invested in hardware instead.  Right?

[Bogart]

So received my Nov Jupiter.

Can't connect to machine by either SSH or webpage.  It is assigned an IP address just can't connect. Even ping gets no response but not sure if the BBB is setup to respond to ping.

If I disconnect all 4 ASIC boards I can connect to the host and access web gui with no issues.  
Reconnect the ASIC boards, can't connect.  
Tried connecting just one ASIC board with same results.
Tried two different power supplies with the same results.

Anyone had anything like this or am I just SOL?

That is an odd one.

You might try reflashing the November firmware onto it.  Maybe you got one with October firmware on it by accident and that's causing it to hang during boot?

[DPoS]

Anyone else seeing 630gh on the new Jupiters? Some readings on the first module seem off.

they went back to an 8 VRM design...  epic lulz...  (we don't need no sticking 8 since we aint got enough of the early ones and rigged it with 4)

[Bogart]

Anyone else seeing 630gh on the new Jupiters? Some readings on the first module seem off.

hno on IRC said that bertmod is not expected to work correctly with the November batch, in particular reading the DCDC data.

[Biffa]

So received my Nov Jupiter.

Can't connect to machine by either SSH or webpage.  It is assigned an IP address just can't connect. Even ping gets no response but not sure if the BBB is setup to respond to ping.

If I disconnect all 4 ASIC boards I can connect to the host and access web gui with no issues.  
Reconnect the ASIC boards, can't connect.  
Tried connecting just one ASIC board with same results.
Tried two different power supplies with the same results.

Anyone had anything like this or am I just SOL?

Maybe silly question but you didn't flash 0.99-tune onto it did you?

If not...

I'd get the RMA email done right away, you can always cancel it if you fix it, but at least get the ball rolling as it can take a day or two, then I'd go on the IRC channel and ask hno what he thinks

[Beans]

Anyone else seeing 630gh on the new Jupiters? Some readings on the first module seem off.

hno on IRC said that bertmod is not expected to work correctly with the November batch, in particular reading the DCDC data.

It's probably reading it correctly. KNC said I may be able to correct it when the tuning firmware is released.

[rolling]

Got a November Jupiter yesterday with absolutely no thermal compound on any of the chips.  Just shiny metal on shiny metal. Be sure to check before powering up.