|
zurg
|
 |
January 27, 2014, 11:29:26 PM |
|
Ok guys, I need some assistance  I had an August kit with 2 boards (~47Gh/s) so the M-Board is V1.0 on Friday I got 10 more boards and placed them 1st in-line then added my 2 pre-existing boards with last board being EOL one. All this was powered by a 1Kw PS that died on me Sunday evening. So I had it running about 48 hours. All the new boards are stock = not overclocked. Now I placed a spare 430W PS on the BF rig and it runs, however I can only see 96 chips running = 1st 6 cards. Any ideas why it doesn't see the rest? Thanks you can do test on pcb that mboard did not see if it's working ok by itself. Looks likew the card ain't working  RMA time What test did you do to determine the card wasn't working? I tried the card just by itself and actually changed it's position in the chain. Didn't matter where I placed it, as any card after it was not showing at all. (including this card)
|
|
|
|
|
CCCrypto
Newbie
Offline
Activity: 28
Merit: 0
|
 |
January 28, 2014, 02:22:49 AM |
|
I tried the card just by itself and actually changed it's position in the chain. Didn't matter where I placed it, as any card after it was not showing at all. (including this card)
Okay, thanks. That will be helpful to remember for future troubleshooting.
|
|
|
|
|
cypherdoc
Legendary
Offline
Activity: 1764
Merit: 1009
|
 |
January 28, 2014, 09:32:13 PM |
|
ok, now it's happening to me; again.
absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).
what were all the suggestions given for this frequent problem?
|
|
|
|
|
|
Keefe
|
 |
January 28, 2014, 10:11:21 PM |
|
ok, now it's happening to me; again.
absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).
what were all the suggestions given for this frequent problem?
I've said it many times before, so I'll let you scroll up for details, but you need to check the output of chainminer and the proxies.
|
|
|
|
cypherdoc
Legendary
Offline
Activity: 1764
Merit: 1009
|
 |
January 28, 2014, 11:46:28 PM |
|
ok, now it's happening to me; again.
absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).
what were all the suggestions given for this frequent problem?
I've said it many times before, so I'll let you scroll up for details, but you need to check the output of chainminer and the proxies. i only have 2 screens: pi@192-168-7-243:~$ sudo screen -r There are several suitable screens on: 2069..192-168-7-243 (28/01/14 23:39:27) (Detached) 2063..192-168-7-243 (28/01/14 23:39:27) (Detached)
here's some of the output of 2069: JOB 145 PROCESSED 0.005 sec [nonces:0 errors:368 spi:48 miso:67 dup:0] (queue:0) JOB 146 PROCESSED 0.006 sec [nonces:0 errors:366 spi:51 miso:67 dup:0] (queue:0) JOB 147 PROCESSED 0.011 sec [nonces:0 errors:427 spi:50 miso:67 dup:0] (queue:0) JOB 148 PROCESSED 0.003 sec [nonces:0 errors:276 spi:34 miso:68 dup:0] (queue:0) JOB 149 PROCESSED 0.002 sec [nonces:0 errors:121 spi:27 miso:56 dup:0] (queue:0) JOB 150 PROCESSED 0.005 sec [nonces:0 errors:357 spi:42 miso:65 dup:0] (queue:0) JOB 151 PROCESSED 0.007 sec [nonces:0 errors:484 spi:33 miso:64 dup:0] (queue:0) JOB 152 PROCESSED 0.005 sec [nonces:0 errors:394 spi:21 miso:68 dup:0] (queue:0) JOB 153 PROCESSED 0.007 sec [nonces:0 errors:548 spi:55 miso:61 dup:2] (queue:0) JOB 154 PROCESSED 0.005 sec [nonces:0 errors:426 spi:57 miso:60 dup:0] (queue:0) JOB 155 PROCESSED 0.006 sec [nonces:0 errors:524 spi:40 miso:68 dup:2] (queue:0) JOB 156 PROCESSED 0.005 sec [nonces:0 errors:382 spi:52 miso:65 dup:0] (queue:0) JOB 157 PROCESSED 0.006 sec [nonces:0 errors:373 spi:41 miso:63 dup:0] (queue:0) JOB 158 PROCESSED 0.004 sec [nonces:0 errors:357 spi:11 miso:58 dup:0] (queue:0) JOB 159 PROCESSED 0.006 sec [nonces:0 errors:420 spi:56 miso:64 dup:0] (queue:0) and some of 2063: 2014-01-28 23:43:18,070 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:19,099 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:20,026 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:21,051 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:22,077 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:23,104 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:24,031 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:25,057 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:26,084 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:27,109 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:28,035 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:29,061 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:30,088 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:44:06,631 DEBUG protocol protocol.lineReceived # > {u'params': [u'37f1', u'88e467b50f54143fe5be3226344ec74608e47c53696c43740000000000000000', u'01000000010000000000000000000000000000000000000000000000000000000000000000ffffffff2703495104062f503253482f04eb40e85208', u'0d2f7374726174756d506f6f6c2f00000000015d1fe595000000001976a9141157b2fc397d2cf3161313d220017d0dba368db588ac00000000', [u'3f23b91dd29e182079db07b2ba415833c38118042b59ce5b212fca23d27092de', u'66dd511b2faf371bb39c8d93932d028117a97d5295a969757ce7a18bacfd5773', u'9d880202be148bc6c31caddc7562a36ea29676a3fde0200926fd39eae9a2f578', u'0c6d9ee7f9d8854354660349dd09689810db94e36e83d266f767f55267b02642', u'60797fb71da5a528d5244dec03eef24a83006f15eb4f82077de8d048d4c198ac', u'9fd0193634d5b229f850792b0fdebabfc359b5818e01710bed9174002f62a8ca', u'a07dadf4444bda448cc6db75f4060857cae3e0cf04b3bf465876caeb77a88844', u'cccc0a87384a359e2e019f4cb5857c7436c4f599834fb9bd245ddc7f834755b2', u'b8017af8253690aba7b706cfbaa635cc30d4e12736ff8a4518173d713470a8b2', u'bdb8e2711c4a3755bbb36127598da1af92e671ad568928273bbd8177a24fc398'], u'00000002', u'1901f52c', u'52e840e3', False], u'id': None, u'method': u'mining.notify'} 2014-01-28 23:44:06,634 INFO proxy client_service.handle_event # New job 37f1 for prevhash 88e467b5, clean_jobs=False
|
|
|
|
|
|
daddyfatsax
|
 |
January 29, 2014, 03:03:01 AM |
|
[2014-01-29 02:51:56] BSB 1cj: 8 of the last 9 results were bad, reinitializing
Can anyone tell me how to disable that chip in bfgminer? I have tried using 53, 54, etc. and I keep getting the above message. Other than that everything is fine. Thanks!
|
|
|
|
|
|
Keefe
|
 |
January 29, 2014, 07:05:37 AM |
|
ok, now it's happening to me; again.
absolutely no hashing with one of my 14 card rigs. changed out SD cards and raspi. can login into admin page but no hashing. took rig apart and checked for any burnt boards (none) and blew out M board connector in case of excess oxidation (none apparent).
what were all the suggestions given for this frequent problem?
I've said it many times before, so I'll let you scroll up for details, but you need to check the output of chainminer and the proxies. i only have 2 screens: pi@192-168-7-243:~$ sudo screen -r There are several suitable screens on: 2069..192-168-7-243 (28/01/14 23:39:27) (Detached) 2063..192-168-7-243 (28/01/14 23:39:27) (Detached)
here's some of the output of 2069: JOB 145 PROCESSED 0.005 sec [nonces:0 errors:368 spi:48 miso:67 dup:0] (queue:0) JOB 146 PROCESSED 0.006 sec [nonces:0 errors:366 spi:51 miso:67 dup:0] (queue:0) JOB 147 PROCESSED 0.011 sec [nonces:0 errors:427 spi:50 miso:67 dup:0] (queue:0) JOB 148 PROCESSED 0.003 sec [nonces:0 errors:276 spi:34 miso:68 dup:0] (queue:0) JOB 149 PROCESSED 0.002 sec [nonces:0 errors:121 spi:27 miso:56 dup:0] (queue:0) JOB 150 PROCESSED 0.005 sec [nonces:0 errors:357 spi:42 miso:65 dup:0] (queue:0) JOB 151 PROCESSED 0.007 sec [nonces:0 errors:484 spi:33 miso:64 dup:0] (queue:0) JOB 152 PROCESSED 0.005 sec [nonces:0 errors:394 spi:21 miso:68 dup:0] (queue:0) JOB 153 PROCESSED 0.007 sec [nonces:0 errors:548 spi:55 miso:61 dup:2] (queue:0) JOB 154 PROCESSED 0.005 sec [nonces:0 errors:426 spi:57 miso:60 dup:0] (queue:0) JOB 155 PROCESSED 0.006 sec [nonces:0 errors:524 spi:40 miso:68 dup:2] (queue:0) JOB 156 PROCESSED 0.005 sec [nonces:0 errors:382 spi:52 miso:65 dup:0] (queue:0) JOB 157 PROCESSED 0.006 sec [nonces:0 errors:373 spi:41 miso:63 dup:0] (queue:0) JOB 158 PROCESSED 0.004 sec [nonces:0 errors:357 spi:11 miso:58 dup:0] (queue:0) JOB 159 PROCESSED 0.006 sec [nonces:0 errors:420 spi:56 miso:64 dup:0] (queue:0) and some of 2063: 2014-01-28 23:43:18,070 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:19,099 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:20,026 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:21,051 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:22,077 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:23,104 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:24,031 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:25,057 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:26,084 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:27,109 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:28,035 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:29,061 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:43:30,088 INFO proxy getwork_listener._on_authorized # Worker '243' asks for new work 2014-01-28 23:44:06,631 DEBUG protocol protocol.lineReceived # > {u'params': [u'37f1', u'88e467b50f54143fe5be3226344ec74608e47c53696c43740000000000000000', u'01000000010000000000000000000000000000000000000000000000000000000000000000ffffffff2703495104062f503253482f04eb40e85208', u'0d2f7374726174756d506f6f6c2f00000000015d1fe595000000001976a9141157b2fc397d2cf3161313d220017d0dba368db588ac00000000', [u'3f23b91dd29e182079db07b2ba415833c38118042b59ce5b212fca23d27092de', u'66dd511b2faf371bb39c8d93932d028117a97d5295a969757ce7a18bacfd5773', u'9d880202be148bc6c31caddc7562a36ea29676a3fde0200926fd39eae9a2f578', u'0c6d9ee7f9d8854354660349dd09689810db94e36e83d266f767f55267b02642', u'60797fb71da5a528d5244dec03eef24a83006f15eb4f82077de8d048d4c198ac', u'9fd0193634d5b229f850792b0fdebabfc359b5818e01710bed9174002f62a8ca', u'a07dadf4444bda448cc6db75f4060857cae3e0cf04b3bf465876caeb77a88844', u'cccc0a87384a359e2e019f4cb5857c7436c4f599834fb9bd245ddc7f834755b2', u'b8017af8253690aba7b706cfbaa635cc30d4e12736ff8a4518173d713470a8b2', u'bdb8e2711c4a3755bbb36127598da1af92e671ad568928273bbd8177a24fc398'], u'00000002', u'1901f52c', u'52e840e3', False], u'id': None, u'method': u'mining.notify'} 2014-01-28 23:44:06,634 INFO proxy client_service.handle_event # New job 37f1 for prevhash 88e467b5, clean_jobs=False
Hmm, that hasn't happened to me yet, so I don't know what's the problem. It seems the chips are getting work but are returning tons of bad nonces and other errors. Is this a multi-bank M-board? My first thought is a bad connection, but it's too coincidental for all banks to do that at once. Maybe one of the voltage regulators on the M-board went bad? One should be ~1.8v and the other ~5v. The 5v just powers the rPi, so must be ok. But I can imagine bad 1.8v for chip comm causing weird results like this.
|
|
|
|
matt4054
Legendary
Offline
Activity: 1946
Merit: 1038
|
 |
January 29, 2014, 05:31:02 PM |
|
Hey guys, I'm sorry if this has been asked a thousand times already, but I have RTFM and OP, and I see nothing about cooling. My H-cards came with heatsinks. I don't want to OC the chips at this stage, and my ambient temp is around 20°C. Can I start hashing without active cooling (i.e. fans), just with the heatsinks? The photo in OP doesn't even have heatsinks. Or is it so obvious that you shouldn't run these without fans, that it's not written anywhere?  Thanks guys! I sold off my CEX.io GHS to buy these, it's just cheaper for more hashrate. Yay!
|
|
|
|
|
|
bobcaticus
|
 |
January 29, 2014, 06:23:10 PM |
|
Hey guys, I'm sorry if this has been asked a thousand times already, but I have RTFM and OP, and I see nothing about cooling. My H-cards came with heatsinks. I don't want to OC the chips at this stage, and my ambient temp is around 20°C. Can I start hashing without active cooling (i.e. fans), just with the heatsinks? The photo in OP doesn't even have heatsinks. Or is it so obvious that you shouldn't run these without fans, that it's not written anywhere?  Thanks guys! I sold off my CEX.io GHS to buy these, it's just cheaper for more hashrate. Yay! You'll need to aim a fan at the rig. Chips run hot and need blown air.
|
|
|
|
|
matt4054
Legendary
Offline
Activity: 1946
Merit: 1038
|
 |
January 29, 2014, 08:04:55 PM |
|
You'll need to aim a fan at the rig. Chips run hot and need blown air.
Thanks for your answer! As I didn't have any spare fan left, I used the one of my BE Blades to create an air tunnel. Air blows to BF first, then the Blades ;-) It's happily hashing now. I guess there's no thermal probe onboard as I don't see any temp reading in the web interface, right? So I guess I should just do as for the BE Blades, stick an external probe on one of the boards
|
|
|
|
|
|
zurg
|
 |
January 30, 2014, 10:02:03 PM |
|
Well, I am at a loss of whats going on with my setup. Got replacement card and the rig been mining about 12 hours. Now I get notification of hashrate drop. I login to see a few of the cards at Zero. Reboot Pi and only first 3 cards are hashing. My room is at a constant 60F with fans blowing over the cards. 
|
|
|
|
|
|
Keefe
|
 |
January 30, 2014, 11:17:17 PM |
|
Well, I am at a loss of whats going on with my setup. Got replacement card and the rig been mining about 12 hours. Now I get notification of hashrate drop. I login to see a few of the cards at Zero. Reboot Pi and only first 3 cards are hashing. My room is at a constant 60F with fans blowing over the cards.  Set all chip speeds to something slow like 50 with autotune off, and restart chainmminer. If the problem persists, reseat the cards.
|
|
|
|
|
zurg
|
 |
January 30, 2014, 11:23:38 PM |
|
Well, I am at a loss of whats going on with my setup. Got replacement card and the rig been mining about 12 hours. Now I get notification of hashrate drop. I login to see a few of the cards at Zero. Reboot Pi and only first 3 cards are hashing. My room is at a constant 60F with fans blowing over the cards.  Set all chip speeds to something slow like 50 with autotune off, and restart chainmminer. If the problem persists, reseat the cards. Just got to work and shut the miner off. I moved it and realigned the fans etc...to be sure that none of the cards are vibrating. All the boards started up... Guess I'll have to keep a close eye on them and have my laser digital thermometer at the ready. Now praying for this 1 day 14 hours block to be finally solved. lol
|
|
|
|
|
Aeonstar2000
Newbie
Offline
Activity: 2
Merit: 0
|
 |
January 31, 2014, 11:41:34 AM |
|
How do i contact support directly? 
|
|
|
|
|
|
zurg
|
 |
January 31, 2014, 12:17:58 PM |
|
|
|
|
|
|
|
daddyfatsax
|
 |
February 04, 2014, 01:16:46 AM Last edit: February 04, 2014, 02:12:10 AM by daddyfatsax |
|
So I get home today and only one of my 8 cards is hashing. I have no clue where to start. The outputs are below. The stratum proxy looks good, not sure what happened and why the other 7 boards will not work. I have re-seated all the cards, tried rocking them, and moved them around to different slots. Anyone have anything else I can try?
GNU nano 2.2.6 File: /run/shm/.stat.log
1 AIfDSo 52 1.935 1.943 50 0 0 1 0 68 [4:0] 708 3 3 3 3 3 3 3 3 3 4 4 3 3 3 3 3 $ 2 AIfDSo 52 1.973 2.028 51 0 0 0 0 71 [4:1] 706 3 3 4 4 4 3 3 3 3 3 3 3 3 3 3 3 $ 3 AIfDSo 52 2.360 1.885 61 0 0 0 0 66 [4:2] 697 4 4 4 4 4 3 3 3 4 4 4 4 4 4 4 4 $ 4 AIfDSo 52 2.283 1.885 59 0 0 0 0 66 [4:3] 702 4 4 4 4 4 4 3 3 3 3 3 4 4 4 4 4 $ 5 AIfDSo 52 1.973 1.943 51 0 0 0 0 68 [4:4] 708 3 3 3 3 3 3 4 4 4 3 3 3 3 3 3 3 $ 6 AIfDSo 52 2.051 1.857 53 0 0 0 0 65 [4:5] 703 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 3 $ 7 AIfDSo 52 2.244 2.114 58 0 0 0 0 74 [4:6] 699 4 4 4 4 4 4 4 3 3 3 3 3 3 4 4 4 $ 8 AIfDSo 52 2.051 1.828 53 0 0 0 0 64 [4:7] 703 3 3 3 3 3 3 4 4 4 4 4 3 3 3 3 3 $ 9 AIfDSo 52 1.896 2.028 49 0 0 0 0 71 [4:8] 709 3 3 3 3 3 3 3 3 3 4 3 3 3 3 3 3 $ 10 AIfDSo 52 2.322 1.914 60 0 0 0 0 67 [4:9] 697 4 4 3 3 3 3 4 4 4 4 4 4 4 4 4 4 $ 11 AIfDSo 52 2.515 2.000 65 0 0 0 0 70 [4:A] 695 4 4 4 4 4 4 4 4 4 5 4 4 4 4 4 4 $ 12 AIfDSo 52 2.244 1.943 58 2 0 0 0 68 [4:B] 699 4 4 4 4 4 3 3 3 3 4 4 4 3 4 4 3 $ 13 AIfDSo 52 2.283 1.914 59 2 0 0 0 67 [4:C] 697 4 4 3 3 4 4 4 3 3 3 4 4 4 4 4 4 $ 14 AIfDSo 52 1.664 1.914 43 0 0 0 0 67 [4:D] 715 3 3 3 3 3 3 3 3 3 3 2 2 2 2 2 3 $ 15 AIfDSo 52 1.780 1.828 46 1 0 0 0 64 [4:E] 710 3 3 3 3 3 3 3 3 3 3 3 3 1 3 3 3 $ 16 AIfDSo 52 1.741 2.085 45 0 0 0 0 73 [4:F] 712 3 3 3 3 3 2 2 2 3 3 3 3 3 3 3 3 $ 17 AIfDSo 52 0.000 1.571 0 571 37 56 17 55 [5:0] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 18 AIfDSo 52 0.000 1.714 0 582 42 23 13 60 [5:1] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 19 AIfDSo 52 0.000 1.714 0 588 46 25 23 60 [5:2] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 20 AIfDSo 52 0.000 1.543 0 541 41 32 18 54 [5:3] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 21 AIfDSo 52 0.000 1.857 0 619 45 23 9 65 [5:4] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 22 AIfDSo 52 0.000 1.657 0 593 41 31 10 58 [5:5] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 23 AIfDSo 52 0.000 1.828 0 616 51 32 4 64 [5:6] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 24 AIfDSo 52 0.000 1.600 0 572 38 35 4 56 [5:7] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 25 AIfDSo 52 0.000 1.828 0 629 47 24 4 64 [5:8] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 26 AIfDSo 52 0.000 1.657 0 530 41 31 14 58 [5:9] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 27 AIfDSo 52 0.000 1.514 0 553 41 31 10 53 [5:A] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 28 AIfDSo 52 0.000 1.685 0 589 43 27 5 59 [5:B] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 29 AIfDSo 52 0.000 1.571 0 526 41 29 10 55 [5:C] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 30 AIfDSo 52 0.000 1.628 0 572 45 33 10 57 [5:D] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 31 AIfDSo 52 0.000 1.971 0 620 51 27 15 69 [5:E] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 32 AIfDSo 52 0.000 1.800 0 610 49 24 11 63 [5:F] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 33 AIfDSo 52 0.000 1.657 0 577 42 29 10 58 [6:0] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 34 AIfDSo 52 0.000 1.714 0 533 44 27 9 60 [6:1] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 35 AIfDSo 52 0.000 1.485 0 520 41 32 17 52 [6:2] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ [ Read 70 lines ] ^G Get Help ^O WriteOut ^R Read File ^Y Prev Page ^K Cut Text ^C Cur Pos ^X Exit ^J Justify ^W Where Is ^V Next Page ^U UnCut Text ^T To Spell
GNU nano 2.2.6 File: /run/shm/.stat.log
34 AIfDSo 52 0.000 1.714 0 533 44 27 9 60 [6:1] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 35 AIfDSo 52 0.000 1.485 0 520 41 32 17 52 [6:2] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 36 AIfDSo 52 0.000 1.714 0 634 41 25 14 60 [6:3] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 37 AIfDSo 52 0.000 1.857 0 668 43 30 10 65 [6:4] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 38 AIfDSo 52 0.000 1.657 0 576 44 30 8 58 [6:5] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 39 AIfDSo 52 0.000 1.657 0 577 43 31 8 58 [6:6] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 40 AIfDSo 52 0.000 1.571 0 582 45 29 6 55 [6:7] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 41 AIfDSo 52 0.000 1.800 0 576 43 30 8 63 [6:8] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 42 AIfDSo 52 0.000 1.657 0 572 40 31 6 58 [6:9] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 43 AIfDSo 52 0.000 1.400 0 540 37 33 10 49 [6:A] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 44 AIfDSo 52 0.000 1.743 0 588 45 27 11 61 [6:B] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 45 AIfDSo 52 0.000 1.828 0 599 45 28 2 64 [6:C] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 46 AIfDSo 52 0.000 1.771 0 601 45 24 9 62 [6:D] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 47 AIfDSo 52 0.000 1.543 0 623 43 32 8 54 [6:E] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 48 AIfDSo 52 0.000 1.628 0 648 40 28 19 57 [6:F] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 49 AIfDSo 52 0.000 1.771 0 616 46 30 10 62 [7:0] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 50 AIfDSo 52 0.000 1.771 0 609 44 33 11 62 [7:1] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 51 AIfDSo 52 0.000 1.714 0 578 41 30 10 60 [7:2] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 52 AIfDSo 52 0.000 1.800 0 590 51 27 11 63 [7:3] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 53 AIfDSo 52 0.000 1.543 0 541 46 31 9 54 [7:4] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 54 AIfDSo 52 0.000 1.628 0 572 39 31 9 57 [7:5] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 55 AIfDSo 52 0.000 1.657 0 564 41 29 7 58 [7:6] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 56 AIfDSo 52 0.000 2.028 0 648 55 27 10 71 [7:7] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 57 AIfDSo 52 0.000 1.771 0 612 44 32 12 62 [7:8] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 58 AIfDSo 52 0.000 1.714 0 578 48 32 10 60 [7:9] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 59 AIfDSo 52 0.000 1.657 0 552 45 33 12 58 [7:A] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 60 AIfDSo 52 0.000 1.743 0 592 46 21 7 61 [7:B] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 61 AIfDSo 52 0.000 1.943 0 649 49 24 12 68 [7:C] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 62 AIfDSo 52 0.000 2.028 0 660 52 26 11 71 [7:D] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 63 AIfDSo 52 0.000 1.485 0 524 39 37 11 52 [7:E] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ 64 AIfDSo 52 0.000 1.771 0 557 51 30 11 62 [7:F] 756 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 $ speed:3328 noncerate[GH/s]:33.315 (0.521/chip) hashrate[GH/s]:112.952 good:861 errors:28172 spi-err:2117 miso-err:1423 duplicates:495 jobs:120 $ board-2 speed nrate hrate good errors spi-err miso-er duplic good bad off per chip good cores 4: 832 33.315 31.109 861 5 0 1 0 16 0 0 (2.082/chip) 7% 5: 832 0.000 27.138 0 9311 699 483 177 16 0 0 (0.000/chip) 0% [ Read 70 lines ] ^G Get Help ^O WriteOut ^R Read File ^Y Prev Page ^K Cut Text ^C Cur Pos ^X Exit ^J Justify ^W Where Is ^V Next Page ^U UnCut Text ^T To Spell
OB 451 PROCESSED 0.002 sec [nonces:8 errors:257 spi:16 miso:15 dup:3] (queue:4) JOB 452 PROCESSED 0.004 sec [nonces:8 errors:217 spi:16 miso:12 dup:4] (queue:2) JOB 453 PROCESSED 0.001 sec [nonces:11 errors:194 spi:11 miso:13 dup:7] (queue:1) JOB 454 PROCESSED 0.002 sec [nonces:7 errors:243 spi:22 miso:12 dup:10] (queue:4) JOB 455 PROCESSED 0.001 sec [nonces:4 errors:245 spi:15 miso:11 dup:5] (queue:1) JOB 456 PROCESSED 0.002 sec [nonces:8 errors:315 spi:22 miso:10 dup:3] (queue:1) JOB 457 PROCESSED 0.001 sec [nonces:10 errors:244 spi:25 miso:12 dup:2] (queue:3) JOB 458 PROCESSED 0.002 sec [nonces:10 errors:277 spi:17 miso:11 dup:6] (queue:2) JOB 459 PROCESSED 0.002 sec [nonces:5 errors:288 spi:22 miso:9 dup:4] (queue:1) JOB 460 PROCESSED 0.001 sec [nonces:5 errors:173 spi:11 miso:14 dup:4] (queue:0) JOB 461 PROCESSED 0.001 sec [nonces:8 errors:222 spi:13 miso:14 dup:6] (queue:1) JOB 462 PROCESSED 0.002 sec [nonces:6 errors:265 spi:21 miso:12 dup:2] (queue:1) JOB 463 PROCESSED 0.002 sec [nonces:15 errors:223 spi:17 miso:12 dup:7] (queue:4) JOB 464 PROCESSED 0.002 sec [nonces:6 errors:278 spi:20 miso:13 dup:1] (queue:2) JOB 465 PROCESSED 0.002 sec [nonces:9 errors:233 spi:20 miso:13 dup:10] (queue:4) JOB 466 PROCESSED 0.001 sec [nonces:7 errors:238 spi:24 miso:12 dup:2] (queue:2) JOB 467 PROCESSED 0.002 sec [nonces:2 errors:269 spi:19 miso:13 dup:4] (queue:0) JOB 468 PROCESSED 0.002 sec [nonces:11 errors:198 spi:17 miso:13 dup:2] (queue:3) JOB 469 PROCESSED 0.002 sec [nonces:4 errors:241 spi:20 miso:10 dup:2] (queue:0) JOB 470 PROCESSED 0.003 sec [nonces:11 errors:265 spi:29 miso:12 dup:3] (queue:5) JOB 471 PROCESSED 0.002 sec [nonces:13 errors:256 spi:19 miso:15 dup:8] (queue:2) JOB 472 PROCESSED 0.002 sec [nonces:10 errors:219 spi:17 miso:12 dup:5] (queue:4) JOB 473 PROCESSED 0.002 sec [nonces:13 errors:245 spi:20 miso:10 dup:6] (queue:4) JOB 474 PROCESSED 0.002 sec [nonces:5 errors:263 spi:23 miso:13 dup:3] (queue:0) JOB 475 PROCESSED 0.002 sec [nonces:8 errors:187 spi:14 miso:10 dup:2] (queue:1) JOB 476 PROCESSED 0.002 sec [nonces:1 errors:238 spi:18 miso:12 dup:8] (queue:0) JOB 477 PROCESSED 0.002 sec [nonces:9 errors:256 spi:21 miso:9 dup:7] (queue:2) JOB 478 PROCESSED 0.002 sec [nonces:6 errors:253 spi:25 miso:10 dup:14] (queue:1) JOB 479 PROCESSED 0.001 sec [nonces:5 errors:160 spi:16 miso:17 dup:5] (queue:0) JOB 480 PROCESSED 0.002 sec [nonces:12 errors:262 spi:21 miso:10 dup:5] (queue:3) JOB 481 PROCESSED 0.002 sec [nonces:6 errors:298 spi:22 miso:11 dup:6] (queue:2) JOB 482 PROCESSED 0.001 sec [nonces:9 errors:209 spi:17 miso:12 dup:3] (queue:1) JOB 483 PROCESSED 0.003 sec [nonces:11 errors:312 spi:26 miso:8 dup:2] (queue:2) JOB 484 PROCESSED 0.001 sec [nonces:8 errors:133 spi:14 miso:13 dup:3] (queue:2) JOB 485 PROCESSED 0.002 sec [nonces:7 errors:252 spi:16 miso:11 dup:8] (queue:3) JOB 486 PROCESSED 0.002 sec [nonces:16 errors:262 spi:23 miso:13 dup:11] (queue:7) JOB 487 PROCESSED 0.002 sec [nonces:7 errors:242 spi:15 miso:11 dup:2] (queue:4) JOB 488 PROCESSED 0.002 sec [nonces:8 errors:265 spi:19 miso:11 dup:6] (queue:0) JOB 489 PROCESSED 0.002 sec [nonces:4 errors:246 spi:18 miso:11 dup:6] (queue:2)
Edit: Narrowed it down to 2 bad boards. It appears the solder on the pins has worn down and the cards are not getting good contact on the M-board slots. Not sure how to fix that.
|
|
|
|
|
Swimmer63
Legendary
Offline
Activity: 1593
Merit: 1004
|
 |
February 04, 2014, 03:41:37 AM |
|
I have a board that has gone from 450 Gh/s to 135. I have tried everything and can't get more than one card per four slot bay.
|
|
|
|
|
|
zurg
|
 |
February 04, 2014, 12:55:33 PM |
|
When some of my cards quit showing up I powered the whole rig down and about 20min later powered it.. all the cards were showing up. Make sure that none of them vibrate if your fan is blowing on them. Also try pulling the 1st non working card and move the rest up. I had 1 card go bad like that and it made the rest of them in the chain not show up at all.
|
|
|
|
|
|
daddyfatsax
|
 |
February 04, 2014, 04:48:17 PM |
|
When some of my cards quit showing up I powered the whole rig down and about 20min later powered it.. all the cards were showing up. Make sure that none of them vibrate if your fan is blowing on them. Also try pulling the 1st non working card and move the rest up. I had 1 card go bad like that and it made the rest of them in the chain not show up at all.
I will try leaving it off for 20 min. My issue is that the first slot for each bank works, ie:0, 4, 8, and C. The rest are not working. No clue what happened.
|
|
|
|
|
|
bobcaticus
|
 |
February 04, 2014, 07:09:18 PM |
|
ventilation and power are key with 90% of hashing / card issues.
If you don't have a fan pointed at your cards, they will overheat and shut off. Turn the rigs on their left hand side (so the SD card is facing down) and aim a good sized fan towards it.
|
|
|
|
|
|