Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux)

[prix]

Radeon rx 470 g1 gaming 4G, ~1270/1810, timings, claymore 9.2, i8: 229 H/s average per card, +6%

same cards , but not more then 209 H/s. 1230/2000 timings from 1500 ,-i 8 , any ideas ?

Maybe slow CPU ? some celeron G series

I have Athlon FX, but I think it's not a big deal. My CPU load is very low.
Have you same model? Gaming G1?
My not works on 2000 memory, even on 1900 MHz (I have 5 cards), but works on lower timings.
And this algo like core frequency more than memory.

And are you using 9.2 version?

[nunoborges]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

[IOTUSA]

There is the proof - https://i.imgsafe.org/949d2c9995.jpg

Got confused with temps and wrote them the other way around but it is what it is.

GPU1 is my RX 470.

That's why people were calling you on it as the numbers didn't make sense.
Now they do so everyone can move on. 220 h/s is quite normal.

He said the speed is 277H/s.

Yes, he got confused.. Let's move on..

Yes, my apologies. 470 has always been listed as GPU1 but 9.2 changed that.

I jumped right into it without checking any further.

My apologies for seeming hostile. Honest mistake
It's just fairly common for people to over-represent hash rates for some reason and it's never good for the community and can lead to newer members making bad decisions on hardware purchases etc.

[Gambler8899]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

Put on stock or underclock.
Check watts (not enough strong psu)
Check risers

[Zefasen]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

Put on stock or underclock.
Check watts (not enough strong psu)
Check risers

Reduce the frequency or reduce the intensity.

[MrJaekin]

Im getting 277 h/s with my RX 470 8gb.

One of my 290s is doing 290 h/s but the other does 220 h/s. Will need to investigate that.

Thanks claymore.

WOW!  290 Sols/s on a 290?  Is this a ref model?  What clocks are you using?  I can't get more than 260 out of mine.

260 sol/s?
You should try flash your cards with Stilt BIOS.
I get 310 sol/s with ref R9 290 Stilt BIOS, 1100 core, 1450 memory.

I have 4 R9 290 Ref Models... This would be great!  Could you point me in the direction of the STILT BIOS you used?

[Golku]

not bad

rx 480 = 250
rx 470 = 225

total power usage = 360 /w system

[IOTUSA]

Im getting 277 h/s with my RX 470 8gb.

One of my 290s is doing 290 h/s but the other does 220 h/s. Will need to investigate that.

Thanks claymore.

WOW!  290 Sols/s on a 290?  Is this a ref model?  What clocks are you using?  I can't get more than 260 out of mine.

260 sol/s?
You should try flash your cards with Stilt BIOS.
I get 310 sol/s with ref R9 290 Stilt BIOS, 1100 core, 1450 memory.

I have 4 R9 290 Ref Models... This would be great!  Could you point me in the direction of the STILT BIOS you used?

Same, I'll give it a whirl on my 290 REF. Whats the wattage per card with bios mod?

[nunoborges]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

Put on stock or underclock.
Check watts (not enough strong psu)
Check risers

Reduce the frequency or reduce the intensity.

I'm only have Stilt bios on them, not overclocked in software, the intensity already tryed to put at "0" about frequency how can i reduce this?

[tiamatt]

Hello friends,

I have 5X Sapphire nitro rx480 4gb on win 8 , the latest driver 16.12.2 , no overclock no bios mod.
When start ,all cards run at 220 h/s but after 5 min slowdown to 170-180 h/s.
I try few combinations 1395/2195   , 1306/1900  but no result.The people report 240-250 h/s for those cards.
Can you help me please with proper settings and driver version.

Thank you very much !

[shadabahmed]

which pool u guys are using right now?

i m asking because

in dwarf after 100 minutes

Current balance 0.0000 ZEC

[melloyellow]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

Put on stock or underclock.
Check watts (not enough strong psu)
Check risers

Reduce the frequency or reduce the intensity.

I'm only have Stilt bios on them, not overclocked in software, the intensity already tryed to put at "0" about frequency how can i reduce this?

You may have to increase the voltage.  Sometimes undervolting works and sometimes overvolting works, you just have to test.  The Stilt's bios for 290 have lowered default voltages except for one, which has a higher default voltage. This one is to be used if the others don't work, I have had to use the higher on some cards but you can reduce the voltage with afterburner to get it just right. If you're increasing voltages for the first time use small increments so you get the hang of it, and watch your temps.

[nunoborges]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

Put on stock or underclock.
Check watts (not enough strong psu)
Check risers

Reduce the frequency or reduce the intensity.

I'm only have Stilt bios on them, not overclocked in software, the intensity already tryed to put at "0" about frequency how can i reduce this?

You may have to increase the voltage.  Sometimes undervolting works and sometimes overvolting works, you just have to test.  The Stilt's bios for 290 have lowered default voltages except for one, which has a higher default voltage. This one is to be used if the others don't work, I have had to use the higher on some cards but you can reduce the voltage with afterburner to get it just right. If you're increasing voltages for the first time use small increments so you get the hang of it, and watch your temps.

Thanks for your reply i will try to do that thanks i will put the results in a bit

[dumpida]

Hi Everyone, first post in here
I Have a question about my rigs, i've got 2 rigs of 290's and one rig that have 5GPU (3x290's and 2x290x) and this rig only works at 100% with Claymore version 7.0 with the new versions i've got warnings from my graphics driver, i allready tryed to put interface at "0" but have the same results anyone had this problem???

Put on stock or underclock.
Check watts (not enough strong psu)
Check risers

Reduce the frequency or reduce the intensity.

I'm only have Stilt bios on them, not overclocked in software, the intensity already tryed to put at "0" about frequency how can i reduce this?

You may have to increase the voltage.  Sometimes undervolting works and sometimes overvolting works, you just have to test.  The Stilt's bios for 290 have lowered default voltages except for one, which has a higher default voltage. This one is to be used if the others don't work, I have had to use the higher on some cards but you can reduce the voltage with afterburner to get it just right. If you're increasing voltages for the first time use small increments so you get the hang of it, and watch your temps.

Thanks for your reply i will try to do that thanks i will put the results in a bit

It is better to under clock as the power supply might not be strong enough. If you have many cards, it is better to lower the clock.

[xeridea]

There is the proof - https://i.imgsafe.org/949d2c9995.jpg

Got confused with temps and wrote them the other way around but it is what it is.

GPU1 is my RX 470.

That's why people were calling you on it as the numbers didn't make sense.
Now they do so everyone can move on. 220 h/s is quite normal.

He said the speed is 277H/s.

Yes, he got confused.. Let's move on..

Yes, my apologies. 470 has always been listed as GPU1 but 9.2 changed that.

I jumped right into it without checking any further.

Press "S" while miner running to show stats, and it will show what cards you have...

[xeridea]

Hello friends,

I have 5X Sapphire nitro rx480 4gb on win 8 , the latest driver 16.12.2 , no overclock no bios mod.
When start ,all cards run at 220 h/s but after 5 min slowdown to 170-180 h/s.
I try few combinations 1395/2195   , 1306/1900  but no result.The people report 240-250 h/s for those cards.
Can you help me please with proper settings and driver version.

Thank you very much !

Don't use newest ReLive driver (16.12.2), it is slower.  Use 16.11.x or older.  If you have bios mods, you must use 16.9.x through 16.11.x, as 16.8.x and earlier check bios signature.

[tiamatt]

Hello friends,

I have 5X Sapphire nitro rx480 4gb on win 8 , the latest driver 16.12.2 , no overclock no bios mod.
When start ,all cards run at 220 h/s but after 5 min slowdown to 170-180 h/s.
I try few combinations 1395/2195   , 1306/1900  but no result.The people report 240-250 h/s for those cards.
Can you help me please with proper settings and driver version.

Thank you very much !

Don't use newest ReLive driver (16.12.2), it is slower.  Use 16.11.x or older.  If you have bios mods, you must use 16.9.x through 16.11.x, as 16.8.x and earlier check bios signature.

Thank you , i will change right now the driver

[iMish]

Hello friends,

I have 5X Sapphire nitro rx480 4gb on win 8 , the latest driver 16.12.2 , no overclock no bios mod.
When start ,all cards run at 220 h/s but after 5 min slowdown to 170-180 h/s.
I try few combinations 1395/2195   , 1306/1900  but no result.The people report 240-250 h/s for those cards.
Can you help me please with proper settings and driver version.

Thank you very much !

that's called thermal throttling, when your cards reach high temps the clock speeds goes down to prevent damaging your gpu

increase max rpm to 3000 in trixx or watttool

[RustNan]

Hello friends,

I have 5X Sapphire nitro rx480 4gb on win 8 , the latest driver 16.12.2 , no overclock no bios mod.
When start ,all cards run at 220 h/s but after 5 min slowdown to 170-180 h/s.
I try few combinations 1395/2195   , 1306/1900  but no result.The people report 240-250 h/s for those cards.
Can you help me please with proper settings and driver version.

Thank you very much !

Don't use newest ReLive driver (16.12.2), it is slower.  Use 16.11.x or older.  If you have bios mods, you must use 16.9.x through 16.11.x, as 16.8.x and earlier check bios signature.

I use 16.9.2 for R9 nano, it works well.

[br2459]

Using Flypool, contemplated switching to dwarf but have seen some posts about them going down so sticking with Flypool for now.

On a related topic Version 9.2 has my Sapphire RX480's 8GB running about 257H/s while my Sapphire 4GB 270x's are running about 155H/s. HD 7970 is still about 200H/s

Clock settings for RX 480 are GPU - 1425 and Mem - 2100
Clock settings for R9 270x are GPU - 1165 and Mem - 1500. I found with the 270x increasing the GPU resulted in higher hashrate but lowered when increasing the Mem clock above 1500
Clock settings for the HD7970 are GPU - 1050 and Mem 1500.